b16a clutch kit, 90-91 teg, 92-93 teg?

[droppedcrxsi]

Hi, I just got my act clutch kit for my b16a, I told them my aplication, and I thought i was getting a clutch for the 90-91 teg, but I got a 92-92 teg kit, will this work, or is it the wrong application. Do 92-93 tegs have different spline count that 90-91? Thanks, Ryan

[droppedcrxsi]

OK, I just read on a site 92 gsr, so I think I am ok, but for some reason I was thinking 90-91 was the correct aplication, so could someone please set me straight so I can stop contradicting myself. Thanks, Ryan

[Phatwhippin_CRX]

90 teg is what I used...... pretty sure that 92/93 tegs have a different spline count, but then again it all depends on your tranny. The YS1 uses a 92/93 disc, while the rest of the trannies use a 90/91 disc....... pretty sure about this

[droppedcrxsi]

What tranny do you have? I have j1, so are you pretty sure I have the wrong part, thanks, Ryan


PS, anyone have a j1? What clutch kit?

[Phatwhippin_CRX]

I had a J1, it blew up

90 Integra clutch disc worked perfectly....

By the way, the pressure plate is the same no matter what year 90-93

[CRXtc]

they are different, due to the tranny change in 92-93......i remember asking that and they specifically asked me what year i had because in 90-91 the disk is different, the splines might line up but the disk is the wrong disk

[droppedcrxsi]

OK, I will buy a new clutch disk, and alignment tool for a 90-91 teg, and just sell my 92-93 clutch disk, and alignment tool on ebay or something. Thanks, I needed to get this straight before I put my clutch in next week. Thanks, Ryan

If this is wrong, please stop me, Thanks!

[droppedcrxsi]

Did the j1 come in 92-93 also, cause if it did, I could still be ok. Let me know, Thanks, Ryan

[droppedcrxsi]

Here is the email.....



----- Original Message -----
> From: "Ryan l Basseri"
> To: <info@advancedclutch.com>
> Sent: Thursday, September 05, 2002 5:03 PM
> Subject: clutch part number question
>
>
> Hi, I just bought a clutch for a integra JDM x-si (b16a1)motor with a
hydro
> j1 tranny. The clutch plate # i recieved was HSD015. I looked on your
site,
> and it was for a 92-93 integra, do I have the right part? Or do I need a
> 90-91 part? If I have the wrong part, can I send it back to trade, let me
> know. Thanks very much, Ryan

Reply....


Ryan:

Yes you have the right Disc, the HSD015 disc fits the B-16 Hydraulic, it
also fits many of our Integra applications.

Great Question, Thanks for asking!!




Dawn M. Morgan
(New Accounts/Sales)

Advanced Clutch Technology
206 East Ave K-4
Lancaster CA, 93535
661-940-7555 ext 206


So, should I go by this? Thanks, Ryan

[Phatwhippin_CRX]

umm....... pretty sure he doesn't know what he's talking about. I mean, I COULD be wrong and all, but first your tranny is cable. Pretty damn sure NO hydro disc fits a cable tranny.

Easy way to check? Get your disc, and slip it onto the splines and see if it fits....

[droppedcrxsi]

oops, yeah, cable that was a typo on my part. This goes to show he dosent know what he is talking about. Ill give him another email, and ask if he could ask someone else. I will try to see if he could just exchange it. Thanks, Ryan