Honda and Acura Car Forums banner

1 - 7 of 7 Posts

·
Registered
Joined
·
62 Posts
Discussion Starter #1
Selling my 2000 Civic Si, electron blue pearl

Exterior:
Custom graphics from X-treme Graphics (will remove if you don't like)
18" Enkei RS-6 wheels w/ Nitto 450 tires
Comes with two matching 15'' Enkei RS-6 wheels w/ BFG drag radials (use these for at the track/good for shows as well)
Also have almost new Bogart Drag-on Fly star polished 13" wheels w/ slicks in front and Bogart 15's with skinnies in rear
Veilside carbon fiber GT wing, electron blue pearl, with polished brackets
Tinted windows
Take your pick: Aerogear Predator hood, electron blue pearl or APC carbon fiber hood (with the matching graphics)
CTR headlights
JDM mirrors
Tsunami T2000 body kit
Brembo rotors
Ground Control coilovers or Skunk 2 drag springs in rear
Tokiko blue shocks in front
Koni yellow adjustable shocks in rear

Interior:
Rick's Racecraft and Chassis custom 6 point roll bar, bolt in, powdercoated electron blue
IO Port roll bar camera mount
ACC black carpet
Momo millenium steering wheel
Momo black/polished e-brake handles w/ boot
Skunk 2 short shifter & shift knob
Polished gauge trim
Greddy turbo timer (custom mounted in carbon fiber in center console w/ space for a Greddy Profec B, sold mine)
Apexi AVC-R
Custom panel with 3 nitrous control switches and 1 button, where stock, head unit was, leave in for use with nitrous system, or take out and I have the stock head unit to put back in
Sparco polished pedals
Sparco Rev seats, black
RJS 5 point camlock harnesses, black
CTR armrest eliminator/ also have stock armrest w/ console
Driver's side 3 gauge pillar, black, with Autometer Cobalt boost, Oil pressure and EGT gauges
Passenger side airbag taken out (still have if you want it back in the car), custom panel made with Autometer gauges mounted, Air/fuel, fuel pressure & water temp Cobalt gauges, in the Autometer carbon fiber mounting cups
Custom mounted AEM EMS under dash on passenger side
Custom mounted MSD box behind passenger seat

Audio:
Boston Acoustics speakers, all four & tweeters
Custom enclosure in the trunk with a flush mounted Boston Acoustics amp and sub
Amp flush mounted in floor where spare tire well is, sub behind it, two polished NX polished billet brackets on each side, with two NX polished bottles
Polished Skunk 2 strut bar behind sub

Engine:
GSR bottom end
CP 8.75:1 pistons (not installed)
Crower crank & rods (not installed)
Darton Pro sleeve kit (not installed)
B16 head, ported and polished by Forrester
Crower valves, springs & retainers
AEM fuel system: fuel rail, fuel pressure regulator & filter
Comptech fuel pump
Crower turbo cams
Skunk 2 cam gears
RevHard exhaust manifold
Tial wastegate
Precision Turbo, T3T4, SC61, polished housing
Custom 3" downpipe, JetHot coated
Thermal 3" exhaust
Or also have 3" exhaust dump, race use only
Nitrous Express single fogger kit, 75 shot, brand new, never sprayed
660cc Blitz injectors or 880 Precision injectors (depending on how you want to setup the car)
JG Edelbrock intake manifold, polished
JG Edelbrock 84mm throttlebody
Greddy Type S Blow-off valve, mounted on polished intake pipe
Greddy Type 24 intercooler, used since August only, polished piping
Greddy polished oil-catch can
ARP head studs
Cometic head gasket
FAL fan
Fluidyne radiator
Magnecor wires
K&N filter
Skunk 2 front camber kit
Skunk 2 polished wire cover and oil cap
Polished Valve cover
LS transmission w/ Quaife LSD or B16 trans w/ Richmond Spool
AC Autotechnic scatter shield
ACT max extreme pressure plate
ACT 6 puck disc
ACT flywheel
Competition Engineering traction bars
Moroso axles
Moroso intermediate shaft
Moroso oil pan
Energy Suspension bushing kit
Xstatic Batcap battery

If anyone is seriously interested, call Stephanie at (847)456-1766 and I'll give you the rest of the details, price, etc...
Located in West Dundee if you want to check out the car
Moving and must sell asap

 

·
Registered
Joined
·
1,104 Posts
thats not EBP :lol2:
 
1 - 7 of 7 Posts
Top