Honda and Acura Car Forums banner
Status
Not open for further replies.
1 - 9 of 9 Posts

·
Registered
Joined
·
164 Posts
Discussion Starter · #1 ·
Sup peoples.. I have been in the works with my EG for a lil while now.. Had to sprinkle sum dust over the motor... Im tryin to predict time slips, and Horsepower....

heres what I have.



94' JDM GS-R

- Type R Intake Manifold (Ported-Polished)
- 4 to 1 headers (Ported-Polished)
- Fuel Pressure Reg.
- Fuel Rail
- MSD IGN. Power Cap. Distrib.
- 8.5 Wires
- Cold Air Intake
- Wiseco High Comp Pistons
- Eagle Rods
- Milled Head (Shaved down)
- New Bearing
- Ferrari Valves, Springs, Ret.
- Type R Cams
- Skunk 2 gears
- Underdrive Pulley
- Block Gaurd
- Head Studs
- Block Studs
- Fuel/Oil Pump
- Full Exhaust no Restriction
- Chipped Mugen Computer
- APEXI
:bomb :bomb :bomb :bomb :bomb :bomb :bomb


How much H/P Time pass on 1/4? or 1/8?
:number1
 

·
Registered
Joined
·
5,494 Posts
half the stuff you listed are variables. You cant just say "high compression pistons and milled head" without giving any numbers, and expect anyone to guess what it will make.

I mean, you listed apex'i......seriously.

"I have greddy weisco and eagle, how much power will it make" thats about all we are getting.

Oh, and a few other parts on your list arent exactly going to do anything at all, expect pull bills out of your wallet.
 

·
Registered
Joined
·
41,903 Posts
lmao hes got headerssssssss!!!!!

You could run anything from 15s to 32nds depending on how bad you drive.
 
  • Like
Reactions: LilGecko96

·
Registered
Joined
·
2,752 Posts
looks like a 14 second build, but then again, i tried to write the word "apexi" on my car and it did nothing for me, maybe ill try and get an "apexi" sticker..........
 

·
Premium Member
Joined
·
29,826 Posts
commador said:
half the stuff you listed are variables. You cant just say "high compression pistons and milled head" without giving any numbers, and expect anyone to guess what it will make.

I mean, you listed apex'i......seriously.

"I have greddy weisco and eagle, how much power will it make" thats about all we are getting.

Oh, and a few other parts on your list arent exactly going to do anything at all, expect pull bills out of your wallet.

werd :kick
 

·
Registered
Joined
·
11,248 Posts
SuperHonda954 said:
Sup peoples.. I have been in the works with my EG for a lil while now.. Had to sprinkle sum dust over the motor... Im tryin to predict time slips, and Horsepower....

heres what I have.



94' JDM GS-R

- Type R Intake Manifold (Ported-Polished)
- 4 to 1 headers (Ported-Polished)
- Fuel Pressure Reg.
- Fuel Rail
- MSD IGN. Power Cap. Distrib.
- 8.5 Wires
- Cold Air Intake
- Wiseco High Comp Pistons
- Eagle Rods
- Milled Head (Shaved down)
- New Bearing
- Ferrari Valves, Springs, Ret.
- Type R Cams
- Skunk 2 gears
- Underdrive Pulley
- Block Gaurd
- Head Studs
- Block Studs
- Fuel/Oil Pump
- Full Exhaust no Restriction
- Chipped Mugen Computer
- APEXI
:bomb :bomb :bomb :bomb :bomb :bomb :bomb


How much H/P Time pass on 1/4? or 1/8?
:number1

You have all of that and you haven't spent $75 to dyno it??? Thread closed.
 
1 - 9 of 9 Posts
Status
Not open for further replies.
Top